This wiring information is being provided free of charge on an «as is» basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Precisionconnections Precisionconnectionsauto.com and/or any comment posted in the comment section by anyone. Assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. This Channel Creator assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.
How To Install A Remote Start Alarm Completely From Start To Finish on Any Honda 2001 2017 1 Hour Training Video Remote Start Detailed Installation on a 2009-2013 Honda Accord any . Installation covers 2000 -2012 HONDA ACCORD. System uses a IDATALINK AL-CA Immobilizer bypass and Door lock control. There is no plug and play kit for this vehicle. This kit is classified as Semi- Plug and Play. Medium Skill level required.
Comes with All connectors and wire ties. All equipment assembled, Programmed, Flash programmed and Configured for a take out of the box installation. Follow all steps in the video for a hassle free installation.
Follow me and add me on
precisionconnectionsauto.com
http://instagram.com/precisionconnections
https://twitter.com/precisionconne1
https://www.facebook.com/preci.connec
Смотреть в источнике
22 комментария
fkn awesome video tnx,,,to the haters and so call perfectionist fk yuo all,,,i been doing installs for 30 years mother fkrs i use this same methods and i gotten no comebacks, soldering is ok , but at times you get cold soldered or bad solder that gets brittle with time,,,,,,like i said in 30 years i seem most of it,,,,,,,,,,,,,,,,,
wow I didn't know that a remote start was this involved
Which one is the starter kill wire ? The purple ?
Good video.. very understandable
I installed a directed 5105. I got the ignition hooked up and the remote start hooked up. I have the break wire going to to break switch. but when i remote start the car i can get in and push the break and the car does not shut off. can you help me out with this.
So professionals dont really care about doing stuff professionally and solder wire? Wtf
Hi, I have installed viper 5901 remote start alarm.
When I start with the remote control and is unlock the doors, the car start but don't lock the doors, if I start the car with the key this locks the doors perfectly, do you know what's wrong?
I have a 1 way Viper 4103xv installed on my F250. I bought it this way and it came with one broke transmitter. It looks as though the program wires are connected to a harness that runs under the top left corner by the cowl panel. I cannot find a program button anyplace, I'm thinking It was wired straight in so I can program the new key fob's by turning the ignition switch x number of times. Would anybody know how to to do this for this model#?
Having taken both dei courses and snake pit training you should always solder your connections.
good job
holllllllllllllllllllllllllllllaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa @ your girl lol
good vid
I need tint and music done and i'm good i don't need any fancy remote start
cookies anyone
I have a 1994 Toyota DLX Pickup I had a Company install my Avital Tornado 1 Alarm many years ago now its not working and my truck wont start… please help .. Thank you
I do see theses Wires coming from the backside of the Key Cylinder.. Large WHITE = Constant 12 Volts , White — Red, Black — Red , Black — Yellow , Blue — Red…. Theses are the wires I see near the ignition key switch. now I just need to know how to hook them back up original factory. so I can get my truck running again. please help !
I do have Pink wire coming to my Ignition Key I see.
Well very helpful and inded easy to understand, and hope you would guide us to the very end of installing the remote system.
Sir, can I split the wires which control the lock and unlock of the remote control unit and join to the corresponding wires/pins (which lock and unlock doors) of the input connector BCM so that by locking or unlocking using the fob key, all doors and all windows are closed automatically at the same time.
In short, lock or unlock with fob=all doors lock or unlock and all windows closed at a time.
Also, if that is possible, I guess no voltage issues will arise on the remote control unit and the BCM unit, since we are only sending pulses to lock, unlock all doors and windows. Kindly ignore this paragraph if I'm mistaken.
Awaiting your utmost help ad reply.
Thanks.
This was an outstanding video very knowledgeable
Yeah I want a remote start and the windows sunroof and trunk to work with my phone
N Ice video my viper starter turns on but the starter keeps running I dont know why can u help me I tryed everything cant figure it out I think I need to hook up tach wire i have a 2011 honda accord but I dont have no idea how to install it or where to install it
To remove and go back to original just go in reverse order?